CVT System Description - Electronic Controls: With 7-speed Mode (CVT)

CVT System Description - Electronic Controls: With 7-speed Mode

Electronic Control System


Electronic Controls Location - 6-position CVT+7Speed Mode

 

 

7Speed Mode Control

The 6-position CVT+7Speed Mode is provided with the 7Speed Mode in the D and S positions. The 7Speed Mode has two modes; the 7-speed automatic mode and 7-speed manual shifting mode. The transmission switches to the 7-speed automatic mode with pushing the 7SPEED MODE main switch. In the 7-speed automatic mode, the transmission can be shifted up and down automatically in 7-stage speeds of pulley ratios, and the steering shift switches are ready to be activated switching to 7-speed manual shifting mode. When the steering shift switch is activated, the 7-speed automatic mode will be cancelled and 7-speed manual shifting mode comes into operation. In the 7-speed manual shifting mode, the driver can shift up and down manually in 7-stage speeds with using the steering shifting switches; much like a manual transmission.
The 7Speed Mode is cancelled by pushing the 7SPEED MODE main switch or when moving the shift lever to any position other than D and S.

The 7SPEED MODE main switch (A), steering shift + (plus) switch (B), and steering shift - (minus) switch (C) are installed on the steering wheel. The driver can select the modes and speed stages with pressing the switches without taking either hand off the steering wheel.

 

The shift indicator (A) and M indicator (B) are in the gauge assembly (C) next to the A/T gear position indicator (D).

 

In the 7-speed automatic mode, the shift indicator displays the number of currently-selected speed stage. The M indicator does not come on in this mode.
In the 7-speed manual shifting mode, the M indicator comes on, and the shift indicator displays the number of the selected speed stage.

Electronic Control System (cont'd)


PCM Terminal Connections - 6-position CVT+7Speed Mode

 

PCM Inputs and Outputs - KB, KE, KG, and KQ Models

NOTE: The illustration shows the example of connector terminal arrangement; connector terminal arrangement varies with the models.

 

PCM CONNECTOR A (31P)
Terminal Number Wire Color Signal Description Measuring Conditions/Terminal Voltage 
A4 BRN PG2 Ground for KB, KE, KG, KQ ( L13A1 engine) models  
A4 BLK PG2 Ground for KQ (L15A1 engine) model  
A5 BLK PG1 Ground  
A10 GRN/BLK SG2 Sensor ground  
A11 GRN/WHT SG1 Sensor ground  
A18 BLU/WHT VABS Vehicle speed sensor signal input With ignition switch ON (II): About 5 V
With ignition switch OFF: 0 V 
A20 YEL/BLU VCC2 Power supply circuit for sensors With ignition switch ON (II): About 5 V
With ignition switch OFF: 0 V 
A21 YEL/RED VCC1 Power supply circuit for sensors With ignition switch ON (II): About 5 V
With ignition switch OFF: 0 V 
A23 BRN/BLK LG2 Ground  
A24 BRN/BLK LG1 Ground  

Electronic Control System (cont'd)


PCM Inputs and Outputs - KB, KE, KG, and KQ Models (cont'd)

NOTE: The illustration shows the example of connector terminal arrangement; connector terminal arrangement varies with the models.

 

PCM CONNECTOR B (24P)
Terminal Number Wire Color Signal Description Measuring Conditions/Terminal Voltage 
B7 GRN/WHT DN LS+ CVT driven pulley pressure control valve power supply positive electrode With ignition switch ON (II): Pulsing signal 
B11 RED/WHT M IND M indicator control for 6-position CVT+7Speed Mode When 7-speed manual shifting mode selected: About 10 V
In other than 7-speed manual shifting mode: 0 V 
B16 YEL SC LS+ CVT start clutch pressure control valve power supply positive electrode With ignition switch ON (II): Pulsing signal 
B19 LT GRN/RED S-DN Steering shift - (minus) switch signal input for 6-position CVT+7Speed Mode With ignition switch ON (II):
  • Steering shift - (minus) switch pressed: 0 V
  • Steering shift - (minus) switch released: About 5 V
 
B20 YEL S-UP Steering shift + (plus) switch signal input for 6-position CVT+7Speed Mode With ignition switch ON (II):
  • Steering shift + (plus) switch pressed: 0 V
  • Steering shift + (plus) switch released: About 5 V
 
B24 BLU/WHT DR LS+ CVT drive pulley pressure control valve power supply positive electrode With ignition switch ON (II): Pulsing signal 

PCM CONNECTOR C (22P)
Terminal Number Wire Color Signal Description Measuring Conditions/Terminal Voltage 
C1 PNK/BLK DN LS- CVT driven pulley pressure control valve power supply negative electrode With ignition switch ON (II): Pulsing signal 
C3 BRN CVT PG2 Ground for KB, KE, KG, KQ ( L13A1 engine) models  
C3 BLK CVT PG2 Ground for KQ ( L15A1 engine) model  
C5 BLK CVT PG1 Ground  
C6 GRN/BLK SOL INH Inhibitor solenoid control With inhibitor solenoid ON (II): Battery voltage
With inhibitor solenoid OFF: 0 V 
C7 RED/BLU NDR CVT drive pulley speed sensor signal input With ignition switch ON (II): 0 V or about 5 V
With engine at idle in the N position: About 2.5 V 
C8 PNK/BLU SC LS- CVT start clutch pressure control valve power supply negative electrode With ignition switch ON (II): Pulsing signal 
C9 BLU/WHT ATP S Transmission range switch S position signal input In the S position: 0 V
In other than S position: About 5 V 
C10 WHT ATP R Transmission range switch R position signal input In the R position: 0 V
In other than R position: About 5 V 
C11 BLU ATP L Transmission range switch L position signal input In the L position: 0 V
In other than L position: About 5 V 
C12 LT GRN ATP NP Transmission range switch P and N position signals input In the P and N positions: 0 V
In other than P and N positions: About 5 V 
C13 YEL M SW 7SPEED MODE main switch signal input for 6-position CVT+7Speed Mode In the 7Speed Mode: 0 V
Released the 7Speed Mode: About 5 V 
C15 WHT NDN CVT driven pulley speed sensor signal input With ignition switch ON (II): 0 V or about 5 V
With engine at idle in the N position: About 2.5 V 
C16 GRN/YEL DR LS- CVT drive pulley pressure control valve power supply negative electrode With ignition switch ON (II): Pulsing signal 
C20 PNK ATP D Transmission range switch D position signal input In the D position: 0 V
In other than D position: About 5 V 
C22 WHT/RED VEL1 CVT speed sensor signal input With ignition switch ON (II): 0 V or about 5 V
With driving (front wheels rotating): About 2.5 V 

Electronic Control System (cont'd)


PCM Inputs and Outputs - KB, KE, KG, and KQ Models (cont'd)

NOTE: The illustration shows the example of connector terminal arrangement; connector terminal arrangement varies with the models.

 

PCM CONNECTOR E (31P)
Terminal Number Wire Color Signal Description Measuring Conditions/Terminal Voltage 
E8 BLU/WHT LED A Shift indicator control for 6-position CVT+7Speed Mode With ignition switch ON (II) and not in the 7Speed Mode: About 5 V
In the 7Speed Mode:
  • 4th, 5th, and 6th speed: About 5 V
  • 1st, 2nd, 3rd, and 7th speed: About 0.3 V
 
E9 YEL/BLK IG1 Power supply circuit for KB, KE, KG models With ignition switch ON (II): Battery voltage
With ignition switch OFF: 0 V 
E9 BLK/YEL IG1 Power supply circuit for KQ model With ignition switch ON (II): Battery voltage
With ignition switch OFF: 0 V 
E11 PNK D IND D indicator control When ignition switch is first turned ON (II): About 6 V for 2 seconds
In the D position: About 10 V 
E13 BLU/RED SLC Shift lock solenoid control With ignition switch ON (II), in the P position, brake pedal pressing, and accelerator pedal released: Battery voltage 
E20 GRN/BLK LED C Shift indicator control for 6-position CVT+7Speed Mode With ignition switch ON (II) and not in the 7Speed Mode: About 5 V
In the 7Speed Mode:
  • 1st, 3rd, and 5th speed: About 5 V
  • 2nd, 4th, 6th, and 7th speed: About 0.3 V
 
E21 RED/WHT LED B Shift indicator control for 6-position CVT+7Speed Mode With ignition switch ON (II) and not in the 7Speed Mode: About 5 V
In the 7Speed Mode:
  • 2nd, 3rd, and 6th speed: About 5 V
  • 1st, 4th, 5th, and 7th speed: About 0.3 V
 
E22 WHT/BLK BK SW Brake pedal position switch signal input Brake pedal pressed: Battery voltage
Brake pedal released: 0 V 
E29 BRN SCS SCS terminal signal input With ignition switch ON (II):
  • SCS terminals open: About 5 V
  • SCS terminals short-circuited to ground: 0 V
 

Circuit Diagram - 6-position CVT+7Speed Mode PCM A/T Control System


KB, KE, KG, and KQ (L15A1 engine) Models

 

Circuit Diagram - 6-position CVT+7Speed Mode PCM A/T Control System (cont'd)


KB, KE, KG, and KQ (L15A1 engine) Models (cont'd)